DANAHER 503-26606-21以太网-TCP/IP模块为MMC提供以太网接入和互联网连接。根据IEEE 802.3规范提供10BaseT连接。数据传输速率为10Mbps。应用程序的范围可以是连接多个MMC、连接多组MMC和PC，或者连接到包括互联网接入的系统。远程编程器访问开关（未来功能）将允许您启用/禁用通过以太网运行的Windows的MMPPro。接通电源后不久，诊断测试运行时，DIAG指示灯短暂点亮。10Base-T端口使用RJ-45型8针连接器，使用100¾非屏蔽双绞线3类或5类电缆（IEEE 802.3第14.4节）。双绞线电缆段的最大长度为100米（328英尺）。注意：该连接器也适用于屏蔽电缆，并将屏蔽接地至机箱。
503-26606-21
对于此版本，使用MMC以太网TCP/IP模块所需的固件必须为7/99或更新版本。在电脑上打开适用于Windows的PiCPro之后，在打开任何文件之前，请使用PiCPro中的“联机”、“状态”菜单项检查MMC EPROM上的日期。通信状态框中列出的第一项是“控制EPROM版本”。如果是7/99之前的版本，则需要下载收到的CD中包含的MMC01.hex文件。使用PiCPro Online，下载十六进制命令。 QDIO1616数字模块用于扩展MSC或MSCII的本地输入和输出(I0)运动控制器。模块安装在DIN导轨上并直接连接到MSCI或MSCII运动控制器，或远程数字/0模块(RDIO)通过内部扩展总线(e总线)。数字1/0的配置按软件通过穆格的中央控制配置轴控软件开发环境。
503-26606-21
The DANAHER 503-26606-21 Ethernet TCP/IP module provides Ethernet access and internet connection for MMC. Provide 10BaseT connections according to IEEE 802.3 specifications. The data transmission rate is 10Mbps. The scope of an application can be connecting multiple MMCs, connecting multiple sets of MMCs and PCs, or connecting to a system that includes internet access. The remote programmer access switch (future feature) will allow you to enable/disable MMPPro for Windows running over Ethernet. Shortly after turning on the power, the diagnostic test ran and the DIAG indicator light briefly lit up. 10Base-T port uses RJ-45 8-pin connector, using 100 ¾ Unshielded twisted pair Category 3 or Category 5 cables (IEEE 802.3 Section 14.4). The maximum length of a twisted pair cable section is 100 meters (328 feet). Note: This connector is also suitable for shielded cables and grounds the shield to the chassis
503-26606-21
For this version, the firmware required to use the MMC Ethernet TCP/IP module must be version 7/99 or later. After opening PiCPro for Windows on your computer, please use the “Online” and “Status” menu items in PiCPro to check the date on the MMC EPROM before opening any files. The first item listed in the communication status box is “Control EPROM version”. If it is a version before 7/99, you need to download the MMC01. hex file included in the received CD. Use PiCPro Online to download hexadecimal commands. The QDIO1616 digital module is used to extend the local input and output (I0) motion controller of MSC or MSCII. The module is installed on a DIN rail and directly connected to the MSCI or MSCII motion controller, or the remote digital/0 module (RDIO) is connected through an internal expansion bus (e-bus). The configuration of the number 1/0 is based on the development environment of the axis control software configured through the central control of Mug.
There are no reviews yet.